Chrysler 200: Operating Instructions — Radio Mode

Chrysler 200: Operating Instructions — Radio Mode

NOTE:
The ignition switch must be in the ON or ACC position to operate the radio.

Power Switch/Volume Control (Rotary)

Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.

Electronic Volume Control

The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.

When the audio system is turned on, the sound will be set at the same volume level as last played.

SEEK Buttons

Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it.

TIME Button

Press the TIME button to alternate display of the time and radio frequency.

Clock Setting Procedure

1. Press and hold the TIME button until the hours blink.

2. Adjust the hours by turning the right side TUNE/ SCROLL control knob.

3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink.

4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change.

5. To exit, press any button/knob, or wait five seconds.

RW/FF

Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies.

TUNE Control

Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.

Setting the Tone, Balance, and Fade

Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones.

Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.

Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.

Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. Turn the TUNE/ SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.

Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers.

Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade

AM/FM Button

Press the buttons to select either AM or FM mode.

SET/RND Button — To Set the Pushbutton Memory

When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.

You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory.

The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.

Every time a preset button is used, a corresponding button number will display.

Buttons 1 - 6

These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).

DISC Button

Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.

Related news

  • Toyota RAV4 Service Manual: Cold start
  • Kia Optima: Control System Composition
  • Toyota Sienna 2010-2018 Owners Manual: Locking and unlocking the doors and key linked functions
  • Chevrolet Sonic Repair Manual: Drum Brake Adjustment
  • Mazda 3 Service Manual: Engine Coolant Leakage Inspection Mzr 2.0, Mzr 2.5

  • Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode

    Chrysler 200: Operating Instructions — Radio Mode