Mazda 3 Owners Manual: Operation

Mazda 3 Owners Manual: Operation

System triggering conditions

The horn sounds intermittently and the hazard warning lights flash for about 30 seconds when the system is triggered by any one of the following:

  • Unlocking a door with the key, door lock switch, or an inside door-lock knob.
  • Forcing open a door, the hood or the liftgate/trunk lid.
  • Opening the hood by operating the hood release handle.
  • Switching the ignition ON without using the push button start.

If the system is triggered again, the lights and horn will activate until the driver's door is unlocked with the transmitter.

(With advanced key)

The lights and horn can also be deactivated by pressing the request switch on a door.

NOTE If the battery goes dead while the theftdeterrent system is armed, the horn will activate and the hazard warning lights will flash when the battery is charged or replaced.

Theft-Deterrent System
If the theft deterrent system detects an inappropriate entry into the vehicle, which could result in the vehicle or its contents being stolen, the alarm alerts the surrounding area of an abnormali ...
How to Arm the System
Close the windows and the moonroof * securely. Switch the ignition OFF. Make sure the hood, the doors, and the liftgate/trunk lid are closed. Press the lock button on the transmitter or ...
Other materials:

Glove Compartment Removal/Installation
CAUTION: If the glove compartment is closed without being joined to the stay damper, the stay damper may be damaged. Verify that the stay damper is joined to the glove compartment before closing the glove compartment. 1. Pull the stay damper in the direction (1) shown in the figu ...

Fuel Filler Cap Inspection [Mzr 2.0, Mzr 2.5]
Leakage Inspection 1. Perform the following SST (Evaporative Emission System Tester 134-01049A) self-test: NOTE: If the tester does not work correctly during self-test, refer to the tester operators manual for more detailed procedures. a. Verify that the gas cylinder valve is c ...

General Procedures (Steering)
Wheel and Tire Installation 1. When installing the wheels and tires, tighten the wheel nuts in a criss-cross pattern to the following tightening torque. Tightening torque 88—118 N·m {9.0—12 kgf·m, 65—87 ft·lbf} Connector Disconnection 1.

Related news

  • Nissan Rogue Service Manual: Removal and installation
  • Buick LaCrosse: California Fuel Requirements
  • Chevrolet Sonic Repair Manual: Windshield Washer Nozzle Replacement
  • Mazda 3 Service Manual: Drive Belt Auto Tensioner Inspection Mzr 2.0, Mzr 2.5
  • Mazda 3 Service Manual: Seat Weight Sensor Calibration Two Step Deployment Control System

  • Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation

    Mazda 3 Owners Manual: Operation