Mazda 3 Service Manual: Seat Belt Inspection

Mazda 3 Service Manual: Seat Belt Inspection

Belt

1. Verify that the belt is installed properly with no twists or kinks.

2. Verify that there is no damage to the seat belt and no deformation of the metal fittings.

  • If there is any malfunction, replace the seat belt.

ELR

Except 5HB (rear center seat belt)

1. Verify that the belt can be pulled out smoothly, and that it retracts smoothly.


  • If there is any malfunction, replace the seat belt.

2. Verify that the retractor locks when the belt is pulled quickly.

  • If there is any malfunction, replace the seat belt.

3. Remove the retractor.

4. While pulling the seat belt out, make sure that the seat belt does not lock when the retractor is tilted slowly up to15°

from the mounted position and locks when the retractor is tilted40° or more.


  • If there is any malfunction, replace the seat belt.

5HB (rear center seat belt)

CAUTION:

  • The rear center seat belt ELR only becomes operable after a certain amount of belt webbing is pulled out. For the ELR inspection, fasten the rear center seat belt to the rear buckle (center) and perform the inspection after pulling out the rear center seat belt 130 mm {5.12 in} (ELR operable condition). If the inspection is performed while the ELR is not in an operable condition, the integrity of the system cannot be determined.

1. Fasten the rear center seat belt to the rear buckle (center) and pull out the rear center seat belt130 mm {5.12 in}

.


2. Verify that the belt can be pulled out smoothly, and that it retracts smoothly.

  • If there is any malfunction, replace the seat belt.

3. Verify that the retractor locks when the belt is pulled quickly.

  • If there is any malfunction, replace the seat belt.

4. Remove the rear center seat belt retractor.

5. While pulling the seat belt out, make sure that the seat belt does not lock when the retractor is tilted slowly up to15°

from the mounted position and locks when the retractor is tilted40° or more.


  • If there is any malfunction, replace the seat belt.

ALR

1. Pull the belt out fully to change the lock mode from ELR to ALR.

2. Verify that retractor makes a clicking sound as the belt slowly retracts. If no sound is heard, the lock mode has not changed to ALR. If necessary, repeat Step 1.

  • If there is any malfunction, replace the seat belt.

3. Verify that the retractor locks when pulled.

  • If there is any malfunction, replace the seat belt.

4. Verify that the lock mode changes to ELR when the belt is fully pulled out.

  • If there is any malfunction, replace the seat belt.

Load Limiter Retractor

WARNING:

  • When the load limiter operates, the belt and anchor rub against each other strongly leaving wear tracks. If the seat belt is used in this state, the seat belt will not function at its full capability and there is the possibility of serious injury to passengers. Be sure to replace the seat belt once the load limiter operates.

1. If the vehicle has been subjected to a shock in an accident, pull the belt from the retractor and confirm that there are no wear tracks (the load limiter has not operated) by visually inspecting and feeling the belt.


  • If there is any malfunction, replace the seat belt.

Other materials:

Antenna Feeder No.2 Removal/Installation
1. Disconnect the negative battery cable.. 2. Remove the rain sensor cover. (Vehicles with auto light/wiper system). 3. Disconnect the rain sensor connector. (Vehicles with auto light/wiper system) 4. Partially peel back the seaming welts. 5. Remove the following parts: a. Sunroof seaming ...

Front ABS Wheel Speed Sensor Inspection
Sensor Output Value Inspection CAUTION: Resistance inspection using other testers may cause damage to the ABS wheel-speed sensor internal circuit. Be sure to use the M-MDS to inspect the ABS wheel-speed sensor. 1. Switch the ignition to off. 2. Connect the M-MDS to the DLC-2. ...

Hazardous Driving
WARNING Be extremely careful if it is necessary to downshift on slippery surfaces: Downshifting into lower gear while driving on slippery surfaces is dangerous. The sudden change in tire speed could cause the tires to skid.

Related news

  • Kia Soul: Seat Belt Buckle Switch (BS). Installation
  • Nissan Maxima: NISSAN Intelligent Key
  • Toyota Corolla Repair Manual: Data listactive test
  • Nissan Altima: Extended storage switch (if soequipped)
  • Kia Soul: Panorama Sunroof Motor Replacement

  • Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection

    Mazda 3 Service Manual: Seat Belt Inspection