Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

Toyota Sienna Service Manual: Front Occupant Classification Sensor RH Collision Detection

DTC B1786 Front Occupant Classification Sensor RH Collision Detection

DESCRIPTION

DTC B1786 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor RH if an accident occurs.

DTC B1786 is also output when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1786 can be cleared by "Zero point calibration" and "Sensitivity check".

Therefore, if DTC B1786 is output, first perform "Zero point calibration" and "Sensitivity check".

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

1 PERFORM ZERO POINT CALIBRATION

  1. Connect the intelligent tester to the DLC3.
  2.  Turn the ignition switch to the ON position.
  3.  Using the intelligent tester, perform "Zero point calibration".

OK: "COMPLETED" is displayed.

2 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check".

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

3 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2.  Clear the DTCs stored in the memory
    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs.

OK: DTC B1786 is not output.

HINT: Codes other than DTC B1786 may be output at this time, but they are not related to this check.

4 REPLACE FRONT SEAT ASSEMBLY RH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Replace the front seat assembly RH ( for flat type, SE-48 for manual seat, SE-58 for power seat).

HINT: Perform the inspection using parts from a normal vehicle if possible.

5 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration".

OK: "COMPLETED" is displayed.

6 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check".

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

7 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2.  Clear the DTCs stored in the memory.

    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs.

OK: DTC B1786 is not output.

HINT: Codes other than DTC B1786 may be output at this time, but they are not related to this check

8 REPLACE OCCUPANT CLASSIFICATION ECU

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the occupant classification ECU

9 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration".

OK: "COMPLETED" is displayed.

10 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check".

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

Other materials:

How to proceed with troubleshooting
1 VEHICLE BROUGHT TO WORKSHOP 2 INSPECT BATTERY VOLTAGE Standard voltage: 11 to 14 V If the voltage is below 11 V, recharge or replace the battery before proceeding. 3 BASIC INSPECTION Turn the ignition switch ON.  Check whether or not the radio receiver turns on. Result 4 CHE ...

Cooling system
On-vehicle inspection 1. INSPECT FOR COOLANT LEAK CAUTION: Do not remove the radiator cap while the engine and radiator are still hot.

Related news

  • Chevrolet Sonic Repair Manual: Instrument Panel Lower Airbag Replacement - Passenger Side
  • Mercedes-Benz E-Class: Manual drive program
  • Chevrolet Sonic Repair Manual: Radio Antenna Base Replacement
  • Hyundai Elantra: EBD(Electronic Brake force Distribution). Description and Operation
  • Nissan Sentra Owners Manual: Keys

  • Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection

    Toyota Sienna Service Manual: Front Occupant Classification Sensor RH CollisionDetection