Toyota Sienna Service Manual: Ignition Coil A Primary

Toyota Sienna Service Manual: Ignition Coil "A" Primary

Ignition Coil "A" Primary

HINT:

  • These DTCs indicate malfunctions relating to the primary circuit.
  • If DTC P0351 is set, check the No. 1 ignition coil with igniter circuit.
  • If DTC P0352 is set, check the No. 2 ignition coil with igniter circuit.
  • If DTC P0353 is set, check the No. 3 ignition coil with igniter circuit.
  • If DTC P0354 is set, check the No. 4 ignition coil with igniter circuit.
  • If DTC P0355 is set, check the No. 5 ignition coil with igniter circuit.
  • If DTC P0356 is set, check the No. 6 ignition coil with igniter circuit.

DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. High-voltage is generated in the secondary wiring and then applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, highvoltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

Ignition Coil "A" Primary

Ignition Coil "A" Primary

Reference: Inspection using an oscilloscope

While cranking or idling, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.

MONITOR DESCRIPTION

MONITOR DESCRIPTION

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.

If the malfunction is not repaired successfully, a DTC is set 1 second after the engine is next started.

MONITOR STRATEGY

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL ENABLING CONDITIONS

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

TYPICAL MALFUNCTION THRESHOLDS

COMPONENT OPERATING RANGE

COMPONENT OPERATING RANGE

WIRING DIAGRAM

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1 CHECK FOR SPARKS AND CHECK SPARK PLUG OF MISFIRING CYLINDER

HINT: (See page ES-211)

2 CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGF1 SIGNAL TERMINAL))

CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGF1 SIGNAL TERMINAL))

(a) Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

(b) Disconnect the E9 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

(d) Reconnect the ECM connector.

(e) Reconnect the ignition coil with igniter connector.

3 INSPECT ECM (IGF1 VOLTAGE)

INSPECT ECM (IGF1 VOLTAGE)

(a) Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

(b) Turn the ignition switch to the ON position.

(c) Measure the voltage according to the value(s) in the table below.

Standard voltage

(d) Reconnect the ignition coil connector.

REPLACE IGNITION COIL ASSEMBLY (See page IG-8)

4 CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGT SIGNAL TERMINAL))

CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGT SIGNAL TERMINAL))

(a) Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

(b) Disconnect the E9 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance :

5 INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5 OR IGT6 VOLTAGE)

INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5 OR IGT6 VOLTAGE)

(a) Turn the ignition switch to the ON position.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage

6 INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5 OR IGT6 VOLTAGE)

INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5 OR IGT6 VOLTAGE)

(a) Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil connector.

(b) Turn the ignition switch to the ON position.

(c) Measure the voltage according to the value(s) in the table below.

Standard voltage

(d) Reconnect the ignition coil connector.

7 INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)

INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)

(a) Disconnect the I1, I2, I3, I4, I5 or I6 ignition coil with igniter connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

(c) Turn the ignition switch to the ON position.

(d) Measure the voltage according to the value(s) in the table below.

Standard voltage

(e) Reconnect the ignition coil with igniter connector.

REPLACE IGNITION COIL ASSEMBLY (See page IG-8)

8 INSPECT RELAY (IG2 RELAY)

INSPECT RELAY (IG2 RELAY)

(a) Remove the IG2 relay from the No. 3 engine room R/B.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

(c) Reinstall the IG2 relay.

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH)

Other materials:

Disassembly
1. REMOVE TRANSFER COVER GASKET (a) Remove the transfer gasket from the transfer assembly. 2. REMOVE TRANSFER CASE BREATHER PLUG (a) Using a screwdriver and a hammer, remove the transfer case breather plug from the No.

Related news

  • Hyundai Elantra: Good driving practices
  • Honda Accord: Recommended Engine Oil
  • Buick LaCrosse: Home Page Features
  • Mazda Mazda6: Door Locks
  • Chevrolet Sonic Owners Manual: Rear Seats

  • Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary

    Toyota Sienna Service Manual: Ignition Coil A Primary