Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

DTC B0112/41 Short to GND in Side Squib RH Circuit

DESCRIPTION

The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0112/41 is recorded when a short to ground is detected in the side squib RH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B0112/41

  • Short circuit in side squib RH wire harness (to ground)
  •  Side squib RH malfunction
  •  Center airbag sensor assembly malfunction
  • Front seat side airbag assembly RH (Side squib RH)
  •  Center airbag sensor assembly
  •  Floor wire No. 2

INSPECTION PROCEDURE

HINT:

  •  Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
  •  After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat side airbag assembly RH.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

CAUTION: Never connect a tester to the front seat side airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs

OK: DTC B0112/41 is not output.

HINT: Codes other than DTC B0112/41 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT SEAT ASSEMBLY RH

2 CHECK FLOOR WIRE NO.2 (SIDE SQUIB RH CIRCUIT)

CHECK FLOOR WIRE NO.2 (SIDE SQUIB RH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire No. 2.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE NO.2

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front seat side airbag assembly RH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B0112/41 is not output. HINT: Codes other than code B0112/41 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Side Squib RH Circuit
DTC B0111/44 Open in Side Squib RH Circuit DESCRIPTION The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH. The circuit instructs ...
Other materials:

Capacity and distribution
Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your ...

Open in Stop Light Switch Circuit
DTC C1249/49 Open in Stop Light Switch Circuit DESCRIPTION This skid control ECU inputs the stop light switch signal and detects the status of brake operation. The skid control ECU has an open detection circuit.

Related news

  • Nissan Rogue Owners Manual: Flexible seating
  • Mazda 3 Service Manual: Charcoal Canister Inspection Mzr 2.0, Mzr 2.5
  • Mazda 3 Owners Manual: Speedometer
  • Toyota Tacoma 2015-2018 Service Manual: Rear Power Outlet Socket
  • Kia Soul: Audio remote control

  • Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit

    Toyota Sienna Service Manual: Short to GND in Side Squib RH Circuit